OpenComms Designer (Fiber/Copper/ISP/Strand/Duct)

New

Fiber and Duct

• 1101682 [Fiber] Modify FTTP BOM>Address Export to include double quotes around Address
• 1176339 [Fiber] Change FTTP BOM Export Addresses to include all addresses
• 1196342 [Fiber] Generic Device Naming Convention
• 1219233 [Fiber] Customer Assignment by Node dialog needs a Customer Status option similar to the Customer Status option in the FTTP Activate Address dialog
• 1219241 [Fiber] Display a message dialog if OS Records are locked during a Rename OS routine.
• 1167383 [Fiber] FTTP Utility-FTTP BOM stops at first device containing ISP equipment.
• 1223178 [Fiber] Add 'More' button to the Xconn dialog for Xconn ISP devices.
• 1219764 [Fiber] Place FTTP command does not create fiber connection between drop and main fiber if there is ISP equipment present in Quick Cross Connect dialog box.
• 1176347 [Fiber] Support for Xconn and WDM splits in the NAP.
• 1197129 [Fiber] Change FTTP command to use new LCC types.
• 1176355 [Fiber] From-To Sheath Naming while Routing
• 918687 [Fiber] Add ability to remove FTTP NIDs/Drops/Customer records by fence.
• 826635 [Fiber] Allow multiple NAPs on Poles or Peds for FTTP Utility.
• 1175362 [Fiber] FTTP Name drops with Options
• 1176330 [Fiber] Fiber Setup-add radio button for Node NID or LCC
• 1176332 [Fiber] Fiber Setup-LCC Check box for most fiber devices in spec file.
• 801565 [OCPV] Apply' and 'OK' buttons should be disabled in Node Connections-Read Only mode.
• 1110309 [Duct] Move Internals' dialog box should display the conduit (Owner and Leased To)

Fixes

Coax

• [Coax] Tap Power Port option allows to uncheck in the Setup when the Powerport is connected in the Power Cable on the map.

Copper

• [Copper] Cable ID field Over lapping to the Ripple check box in the Change Copper Pair dialog box.
• [Copper] In Copper Routing dialog box, Update button is not working.

Duct

• [Duct] Hatches are not cleared in Bentley Duct Element Review dialog box when Owner set to "None" in Conduit Review dialog box.
• [Duct] If "Owner" & "Leased To" are set to "None" & also any cable is not there then it should not allow to create a "Name" in Conduit Review Dialog box.

Fiber

• [Fiber/Copper] "FTTP LCC" option should not be there in Settings of Slack, Copper Terminals & Copper Splits.
• [Fiber/Copper] "Select an equipment type" dialog box closes if we Cancel "Select Equipment-" dialog box two times.
• [Fiber/Copper] If we activated the Calc Distances then fiber routing command is not getting cleared and allows to route copper span from fiber node.
• [Fiber/Copper] OCD app crashes if we hit on incremental or decremental button in Enter ID or name.
• [Fiber/Copper] Using Inside Connection Elevation, The fiber connected to the outside with piggyback ISP equipment should be grayed out in Cross Sections Connections & Quick Cross Connect dialog box
• [Fiber] "Fiber to The Premise" dialog box should be resized.
• [Fiber] "Place FTTP" command creates the another connection in manual connection if the splitter's common connections are already there.
• [Fiber] Activate & Deactivate in Find An Address sections shows "Selected address is already activated" and "Selected address is not activated" respectively.
• [Fiber] After running Place FTTP command, fiber drops does not create connection with ISP equipment ports in Quick Cross Connect dialog box.
• [Fiber] After starting new session of OCD & then running "FTTP Delete" command shows msg as "No locked fiber nodes were found...".
• [Fiber] Connections Check show no Node Ints
• [Fiber] Drop length should accept the minimum value 0.1 in Fiber To the Premise for Place FTTP command.
• [Fiber] Fiber connection should not allow between drop fiber and Allocated port of ISP equipment in Quick Cross Connect dialog box.
• [Fiber] Fiber connections created with ISP port are not seen in Quick Cross Connect dialog box.
• [Fiber] FTTP LCC option should be grayed out if that device is used in network.
• [Fiber] If fiber device is of FTTP LCC type then it should show the warning message while changing to splice enclosure/Non FTTP LCC device.
• [Fiber] In the Fiber module Connections Auto command allows to select Copper Splice enclosure.
• [Fiber] Place FTTP command creates a connection with splitter Out port in Quick Cross Connect at cabinet side but doesn't shows the connection to other side.
• [Fiber] Place FTTP command does not create fiber connections with drop and main fiber at NAP splice enclosure.
• [Fiber] Retain Order Report command never completes -Looping.
• [Fiber] Splicing>Retain Order commands should filter the copper splice enclosure in Select Splice window.
• [Fiber] Starting new session of OCD & running "FTTP Delete" command shows msg as "No locked fiber nodes were found...".
• [Fiber] The available ports left in the LCC cabinet does not show the correct one in FTTP Activate Customer process.
• [Fiber] The FTTP Delete command crashed OCD if used the Merge sheaths command of the FTTP sheaths.
• [Fiber] Trace highlight not displaying on custom line styles when zooming out
• [Fiber] When deleteing OS added master sheath it should pop up message before delete the sheath.
• [Fiber] When we try to delete the hanging fiber span then it opens with the Alert msg related to master sheath for 6 OS(s).